Dual SFP+ Multi-service Platform
All-in-One Optical and Service Test Platform
The dual test port hardware option for the TX300s platform offers a full-featured portable test solution for OTN, SONET/SDH, PDH/DSn, Carrier Ethernet, Fibre Channel and CPRI/OBSAI networks, as well as Synchronization verification tests. This factory-installed hardware option allows the addition of other applications, for example, OTDR, to be installed concurrently in the same test platform.
Highlights
Specifications
Download
Key Features
- All-in-one multi-service test solution
- Dual SFP+ ports support Ethernet interface from 100Base-FX to 10GE, SDH from STM-0 to STM-64, SONET from OC-3 to OC-192, Fibre Channel from 1G to 10G, OTN at OTU1, OTU2, OTU1e/2e and CPRI/OBSAI
- Dual RJ45 ports support 10/100/1000Base-T
- RJ45/Bantam and BNC ports support PDH/DSn and G.703 64k Codirectional electrical interfaces
- Port 1 and Port 2 support independent and simultaneous measurements
- Offers bi-directional Ethernet pass-through monitor test mode
Key Specifications
OTN/SDH/SONET/PDH/DSn
CPRI/OBSAI Testing
- Common Public Radio Interface standard (CPRI): supports all rates from 614.4 Mbps to 9.8304 Gbps
- Open Base Station Architecture Initiative (OBSAI): supports all rates from 768 Mbps to 6.144 Gbps
- Unframed, Layer 1 Framed and Layer 2 (REC/BBU and RE/RRH emulation) BER testing with PRBS stress patterns
- Latency measurements
- CPRI Bi-directional monitoring mode
SCADA and Teleprotection
- IEEE C37.94 Testing
- Terminal and bidirectional pass-through monitor modes
- 64k to 768k (N: 1 to 12)
- BERT, Alarms and Round Trip Delay
- GPS-assisted one-way-latency (asymmetry)
- MMF and SMF optical interfaces
- G.703 64k Codirectional Testing
- Terminal mode
- BERT, Alarms and Round Trip Delay
Ethernet/Fibre Channel
- Dual 10GE LAN/WAN, 1000Base-X, 100Base-FX supported by SFP+ ports
- Dual 10/100/1000Base-T supported by RJ45 ports
- 1G/2G/4G/8G/10G Fibre Channel support for Storage Area Networks
- RFC2544 Throughput, latency, frame loss and back to back tests
- V-SAM test suite compliant with ITU-T Y.1564 standard
- Q in Q (VLAN stacking), MPLS, MPLS-TP, PBB support
- RFC6349 V-PERF TCP test suite
- Bi-directional in-service monitoring with Wireshark on-screen decode
- One way latency with optional built-in GPS
- Fully integrated solution for synchronized packet networks
- Supports IEEE 1588v2/PTP and SyncE/ITU-T G.8261 standards
- Master Clock and Slave clock emulation
- IEEE 1588v2/PTP protocol monitoring and decoding
- IEEE 1588v2/PTP PDV analysis
- Clock recovery from SyncE or PTP and output to physical port
- Wander measurement and MTIE/TDEV analysis
- ESMC SSM generation, monitoring, and decoding
Synchronization Testing
- Clock Wander and Phase (Time Error) Measurements
- MTIE/TDEV Wander Analysis
- Optional built-in chip-scale Atomic Clock
- GPS receiver for disciplining and time alignment
- SyncE and IEEE 1588v2 PTP emulation and Wander measurements